ABEJA GEARS / INDUSTRIAL GEAR MANUFACTURING

Spur gears.Defined foryour drive.

A successful spur gear order starts with the complete mesh: tooth geometry, shaft interface, operating loads, and the evidence required for acceptance. Share a drawing or application brief with ABEJA Gears to align the quotation with your parallel-axis drive and your OEM release process.

Straight teethParallel shaftsApplication-led specification
Concept render of a steel spur gear wheel and pinion with straight teeth.
CONCEPT RENDERStraight-tooth cylindrical geometry

Illustrative geometry. Final design, materials, and manufacturing scope are defined by the agreed specification.

01 / GEOMETRY & INTERFACES

Start with the
complete mesh.

Define the tooth form and the mounting interface together. The design routes below identify different specification decisions; the final manufacturing scope is confirmed during quotation.

01 / DESIGN REVIEW

Standard involute geometry

Straight teeth parallel to the shaft axis provide direct engagement between parallel shafts. Define module or diametral pitch, tooth count, and reference pressure angle for both members of the mesh.

Review togethermating gear data, ratio, reference geometry, and housing center distance.
02 / DESIGN REVIEW

Profile-shifted geometry

Profile shift can address tooth-root geometry and a specified center distance. It changes the tooth proportions and requires a review of the pair rather than an isolated gear diameter.

Review togetherprofile-shift coefficients, working pressure angle, interference, and tooth contact.
03 / DESIGN REVIEW

Shaft and hub integration

The tooth flank must work with the bore, hub, keyway, or shaft arrangement. Establish the functional datums and torque-transfer interface before finalizing tolerances.

Review togetherbore or journal fit, face width, runout datum, axial location, and retention.

02 / ENGINEERING REVIEW

A spur gear works
inside a drive.

Gear geometry, center distance, shaft alignment, and actual operating duty belong in one review. Connect the component drawing to the assembly that will use it.

  1. 01

    Design the entire mesh

    Provide the pinion and mating gear data together. Confirm pitch system, pressure angle, tooth count, profile shift, and working center distance. For a standard, unshifted external pair, the reference center distance is m(z1 + z2)/2; modified tooth geometry needs its own calculation.

  2. 02

    Connect tooth width to shaft support

    Face width is part of the load distribution problem. Share bearing positions, shaft parallelism, housing stiffness, and any overhung arrangement so alignment and deflection can be considered alongside tooth strength.

  3. 03

    Specify behavior under operating conditions

    Share continuous and peak torque, speed, reversals, duty cycle, lubricant, and temperature. Straight-tooth engagement can make noise and vibration relevant at speed; set an assembly-level evaluation method for noise-critical applications.

03 / A QUOTATION YOU CAN COMPARE

Make the RFQ
an engineering brief.

Give engineering and purchasing one set of inputs. Identify open requirements so the quotation can state its assumptions and the agreed manufacturing scope.

Spur Gears project inputs for technical review and quotation
Project inputWhat to shareWhy it matters
Tooth geometryModule or DP; tooth count; pressure angle; profile shift; mating gear drawing.Establishes a compatible mesh and avoids assumptions based only on outside diameter.
Assembly geometryWorking center distance and tolerance; face width; shaft layout; bearing positions.Connects tooth contact and backlash to the housing and shaft support.
Load and dutyOperating speed; continuous, peak, and starting torque; reversals; target life; duty cycle.Gives a meaningful basis for reviewing bending strength, surface durability, and the shaft connection.
Interfaces and materialBore or journals; keyway or spline; datum scheme; material grade; heat-treatment and hardness requirements.Defines how the gear mounts, transfers torque, and is inspected after the agreed processing sequence.
Backlash and acceptanceBacklash type and limits; measurement radius or reference diameter; center distance; temperature; test load and method.Makes a backlash requirement measurable and distinguishes linear tooth clearance from angular lost motion.
Commercial releaseDrawing revision; prototype and annual quantities; release milestones; required reports; delivery destination.Aligns samples, documentation, tooling, packaging, and the production quotation.

Do not have a finished drawing yet? Share the application and the information available. Identify what is fixed, what can change, and what still needs to be established.

04 / AGREED ACCEPTANCE EVIDENCE

Define how the gear
will be accepted.

Translate critical requirements into an inspection and validation scope. Agree the standard, characteristics, sampling, and required records before ordering.

EVIDENCE / 01

Geometry against a named standard

Identify the applicable standard and edition, required grade, and characteristics to report. Specify profile, tooth trace, pitch, and runout checks where they matter to the application; a grade label alone does not define the complete inspection scope.

EVIDENCE / 02

Functional datums and fit

Agree the datum scheme for bore or journal size, radial runout, face runout, hub features, and axial location. Tie each acceptance value to the drawing and the gear's actual mounting interface.

EVIDENCE / 03

Material and heat-treatment evidence

Define which material records, hardness results, and heat-treatment records the order requires. Include case depth or other treatment-specific checks when called out by the specification.

EVIDENCE / 04

Mesh validation under defined conditions

For critical drives, agree a backlash and contact check with the nominated mate and assembly setup. Add an operating noise or vibration test when needed, including speed, load, lubricant, temperature, and pass criteria.

05 / OEM PROGRAM CONTROL

From sample approval
to controlled repeat orders.

Set the release gates your program needs. Keep the drawing, accepted evidence, and change requirements connected as quantities move from samples into production.

01

One controlled specification

Link the drawing revision, mating component, critical characteristics, and inspection plan to the purchase order. Resolve exceptions before the prototype or production release.

02

A defined sample approval gate

Agree the sample quantity, dimensional evidence, functional evaluation, and sign-off criteria. Specify a first-article or customer approval package when your program requires one.

03

Traceability that matches your program

Define the required batch identification, material and treatment records, marking, packaging, and retention period. Confirm the record set and traceability scope in the quotation.

04

Clear change and supply controls

Set expectations for changes to material, processing, tooling, and inspection. Include approval responsibility, forecast assumptions, replenishment quantities, and any required requalification.

START YOUR PROJECT / SPUR GEARS

Bring the complete
mesh into your RFQ.

Send your controlled drawing, mating gear information, and duty conditions. Define the evidence your team needs before prototype approval or production release.

[email protected]

Your starting checklist

  • Pitch system, tooth count, and pressure angle
  • Mating gear and working center distance
  • Face width, bores or journals, and datums
  • Torque, speed, lubrication, and duty cycle
  • Quantity, drawing revision, and acceptance criteria
Download RFQ checklist

06 / BEFORE YOU SEND THE DRAWING

Questions that
change the specification.

Resolve the mesh, operating conditions, and acceptance basis before the order is released.

What information is needed to quote a custom spur gear?

Send a controlled drawing with module or DP, tooth count, pressure angle, face width, bore or shaft features, material, treatment, and acceptance requirements. Include mating gear information, quantities, and the application conditions. If the design is still being developed, share the ratio, center distance, shaft layout, torque, and speed.

Are gears with the same outside diameter interchangeable?

Outside diameter alone is insufficient. Confirm pitch system, pressure angle, tooth count, profile shift, center distance, and the mounting interface. The required mate and operating clearance also need to be considered.

How should backlash be specified?

State whether the requirement is circumferential, normal, or angular backlash, and identify the measurement method and reference location. Include the mating gear, center distance, temperature, and test condition. Lubrication, manufacturing variation, and thermal behavior must be considered when selecting the allowance.

When should spur gears be compared with helical gears?

Compare them when operating speed, acoustic limits, load capacity, or bearing arrangement are central to the design. Spur gears use straight teeth and do not create axial thrust from an ideal aligned tooth mesh. Helical gears introduce an axial force component and use more gradual tooth engagement. Validate the choice against the complete drive.

Can the quotation include OEM approval documents?

List the documents and approval format required by your program, including dimensional reports, material records, treatment evidence, and any first-article or customer-specific package. The quotation should confirm the agreed scope, sampling plan, and submission stage.

Technical references & specification basis

These references explain general gear principles. Product ratings and supplier-specific capabilities in the reference material do not describe ABEJA Gears. The agreed drawing, quotation, and acceptance plan define each order.

Consult